| 1 |
sguazz |
1.1 |
\section{Introduction}
|
| 2 |
|
|
\label{sec:Introduction}
|
| 3 |
|
|
|
| 4 |
lino |
1.4 |
%\section{The Silicon Strip Tracker Layout}
|
| 5 |
|
|
%\label{sec:Layout}
|
| 6 |
|
|
|
| 7 |
carlo |
1.6 |
The CMS SST (Fig. \ref{fig:layout})
|
| 8 |
|
|
covers the radial range between $20\cm$ and $110\cm$ around the LHC
|
| 9 |
sguazz |
1.5 |
interaction point. The barrel region ($| z | < 110\cm$\footnote{A CMS
|
| 10 |
|
|
coordinate system, used through this note, is defined in such a way
|
| 11 |
|
|
that $z$ is the coordinate along the LHC beam axis, $y$ is the
|
| 12 |
|
|
vertical direction and $x$ complete the system; the origin being the
|
| 13 |
|
|
nominal beam interaction point.})
|
| 14 |
|
|
is split into a Tracker Inner Barrel (TIB) made of four detector
|
| 15 |
|
|
layers, and a Tracker Outer Barrel (TOB) made of six detector
|
| 16 |
carlo |
1.6 |
layers. The TIB, being shorter than TOB, is complemented by three Tracker Inner Disks
|
| 17 |
sguazz |
1.5 |
per side (TID), each Disk being in turn composed of three
|
| 18 |
|
|
Rings. The forward and backward
|
| 19 |
|
|
regions ($120\cm < |z| < 280\cm$) are covered by nine Tracker
|
| 20 |
|
|
End-Cap (TEC) disks per side.
|
| 21 |
lino |
1.4 |
The two innermost layers of both TIB and TOB as well as rings number one, two and five
|
| 22 |
sguazz |
1.5 |
of TEC and one and two of TID are instrumented with double-sided
|
| 23 |
|
|
detector modules assemblies able to provide three-dimensional position measurement of the charged
|
| 24 |
|
|
particle hits.
|
| 25 |
carlo |
1.6 |
A complete description of the Silicon Tracker layout %(Fig.\ref{fig:layout})
|
| 26 |
lino |
1.4 |
can be found elsewhere~\cite{ref:layout}.\\
|
| 27 |
|
|
\begin{figure}[!htb]
|
| 28 |
|
|
\begin{center}
|
| 29 |
|
|
\includegraphics[width=0.85\textwidth]{Figs/rz.pdf}
|
| 30 |
|
|
\end{center}
|
| 31 |
|
|
\caption{Longitudinal cross section of one quarter of the CMS SST.
|
| 32 |
|
|
Thicker (blue) segments indicate double-sided silicon microstrip modules.
|
| 33 |
|
|
The nominal beam interaction point is located in (0,0), dimensions are in mm.
|
| 34 |
|
|
The pseudorapidity ($\eta$) coverage is also shown.}
|
| 35 |
|
|
\label{fig:layout} % Give a unique label
|
| 36 |
|
|
\end{figure}
|
| 37 |
sguazz |
1.5 |
|
| 38 |
lino |
1.4 |
The entire tracker is inserted in a carbon fiber Support Tube which is attached to
|
| 39 |
sguazz |
1.5 |
the Electromagnetic Calorimeter. The tracker thermal insulation is
|
| 40 |
|
|
guaranteed by a 'Thermal Shield'. The whole tracker region is embedded into the
|
| 41 |
|
|
3.8~Tesla solenoidal magnetic field.
|
| 42 |
|
|
%Charged particle transverse momentum resolution of about 1.5\% for centrally-produced
|
| 43 |
|
|
%muon of 100~GeV/$c$ is expected~\cite{ref:ptdr}. \\
|
| 44 |
|
|
|
| 45 |
|
|
|
| 46 |
|
|
%The CMS Tracker Inner Barrel (TIB) and Disks (TID) are in the low radius part of the Silicon Strip Tracker (SST)
|
| 47 |
|
|
%of CMS, of which a full description can be found in
|
| 48 |
|
|
%~\cite{ref:CMS1}\cite{ref:CMS2}.
|
| 49 |
|
|
|
| 50 |
|
|
This note reviews the integration of the substructures in which the TIB
|
| 51 |
|
|
and the TID are split to ease the construction,
|
| 52 |
|
|
i.e. the mounting and the test of all components (modules, electronics
|
| 53 |
|
|
and cables) on
|
| 54 |
|
|
%the 16 TIB shell support structures and the 18 TID ring
|
| 55 |
|
|
dedicated mechanical support.
|
| 56 |
|
|
In a second phase, not covered here, these
|
| 57 |
|
|
substructures
|
| 58 |
|
|
%the shells and the rings
|
| 59 |
|
|
will be assembled to build the final TIB and TID
|
| 60 |
|
|
detector.
|
| 61 |
|
|
|
| 62 |
|
|
The note is organized as follows: in section~\ref{sec:layout} the TIB
|
| 63 |
|
|
and TID layouts are described; in section~\ref{sec:} an overview of the main
|
| 64 |
|
|
TIB and TID components is given, with a particular emphasis on the items which are
|
| 65 |
|
|
of particular relevance for the integration activities; in
|
| 66 |
|
|
section~\ref{} and section~\ref{} the integration procedures and the quality control
|
| 67 |
carlo |
1.6 |
tests are throughly reviewed; in section~\ref{} issues related to
|
| 68 |
|
|
detector radiation resistance are discussed.
|
