| 1 |
< |
\section{The TIB/TID Components} |
| 1 |
> |
\section{The Integration Components} |
| 2 |
|
\label{sec:Components} |
| 3 |
|
|
| 4 |
|
\subsection{The Silicon Module} |
| 5 |
|
|
| 6 |
< |
The TIB and TID module consist of a carbon fiber support |
| 6 |
> |
The TIB and TID modules (table~\ref{table:modules}) |
| 7 |
> |
consist of a carbon fiber support |
| 8 |
|
frame that holds a single silicon |
| 9 |
|
sensor~\cite{ref:mask}\cite{ref:sensors} and the front-end electronics |
| 10 |
< |
hybrid circuit. The sensor is aligned with respect to the same frame |
| 11 |
< |
aluminum insets that are used to fix the module the ledges in such a |
| 10 |
> |
hybrid circuit~\cite{ref:hybrid}. |
| 11 |
> |
These detectors are produced from individual, 320~$\mu$m thick, sensors. |
| 12 |
> |
All silicon strip sensors are of the |
| 13 |
> |
single-sided ``p-on-n'' type |
| 14 |
> |
with integrated decoupling capacitors, aluminium readout strips |
| 15 |
> |
and polysilicon bias resistors. |
| 16 |
> |
The sensor is aligned with respect to the same frame |
| 17 |
> |
aluminum inserts that are used to fix the module the ledges in such a |
| 18 |
|
way the sensor positioning is guaranteed with respect to the support |
| 19 |
< |
structure.\\ |
| 20 |
< |
|
| 19 |
> |
structure~\cite{ref:assembly}.\\ |
| 20 |
> |
Double-sided detectors are built by simply assembling two independent |
| 21 |
> |
single-sided modules (``R-Phi'' and ``Stereo'') back to back. |
| 22 |
|
The double-sided TIB layers and TID rings are equipped with module |
| 23 |
|
sandwiches capable of a space point measurement and obtained by |
| 24 |
< |
coupling back-to-back a $r\phi$ module and a special ``stereo'' |
| 25 |
< |
module with the sensor tilted by $100\mrad$. |
| 24 |
> |
coupling back-to-back a ``R-Phi'' module and a special ``Stereo'' |
| 25 |
> |
module with the sensor tilted by $100\mrad$ with respect to the other. |
| 26 |
> |
The stereo sensor and electronics are identical to the R-Phi ones, the only |
| 27 |
> |
difference being in the support mechanics and pitch adapters. \\ |
| 28 |
> |
|
| 29 |
|
|
| 30 |
|
%The stereo module just |
| 31 |
|
%differ from the $r\phi$ one in the details needed to cope with the |
| 32 |
|
%different sensor orientation. |
| 33 |
+ |
\begin{table}[!htb] |
| 34 |
+ |
\begin{center} |
| 35 |
+ |
\caption[smallcaption]{Details on the different TIB/TID modules. } |
| 36 |
+ |
\label{table:modules} |
| 37 |
+ |
%\begin{tabular}{|l||c|c|c|c|c|c|c|} |
| 38 |
+ |
\begin{tabular}{|l|ccccc|} |
| 39 |
+ |
\hline |
| 40 |
+ |
Module & pitch ($\mu$m) & Assembly &Active area & \# of APVs & \# of channels \\ |
| 41 |
+ |
type & & type &$cm^2$ & & per module \\ |
| 42 |
+ |
\hline |
| 43 |
+ |
% \hline |
| 44 |
+ |
TIB Layer 1-2 $r-/phi$ & 80 & DS & 35 & 6 & 768 \\ |
| 45 |
+ |
TIB Layer 1-2 stereo & 80 & DS & 35 & 6 & 768 \\ |
| 46 |
+ |
TIB Layer 3-4 $r-/phi$ & 120 & SS & 35 & 4 & 512 \\ |
| 47 |
+ |
TID Ring 1 $r-/phi$ & 81-119 & DS & 85 & 6 & 768 \\ |
| 48 |
+ |
TID Ring 1 stereo & 81-119 & DS & 85 & 6 & 768 \\ |
| 49 |
+ |
TID Ring 2 $r-/phi$ & 81-119 & DS & 88 & 6 & 768 \\ |
| 50 |
+ |
TID Ring 2 stereo & 81-119 & DS & 88 & 6 & 768 \\ |
| 51 |
+ |
TID Ring 3 $r-/phi$ & 123-158 & SS & 79 & 4 & 512 \\ |
| 52 |
+ |
\hline |
| 53 |
+ |
\end{tabular} |
| 54 |
+ |
\end{center} |
| 55 |
+ |
\end{table} |
| 56 |
|
|
| 57 |
< |
{\bf FIX ME: descrizione/tabella dei vari tipi di moduli.} |
| 57 |
> |
%%{\bf FIX ME: descrizione/tabella dei vari tipi di moduli.} |
| 58 |
|
|
| 59 |
|
%The readout chip |
| 60 |
|
%pitch (44$\mu$m) is matched to the sensor pitch via an aluminum deposited glass substrate |
| 63 |
|
%electronics, is realized using kapton multilayer technology integrating the power and |
| 64 |
|
%signal cables. \\ |
| 65 |
|
|
| 66 |
< |
A single sided module of the TID ring 1 module shown in |
| 67 |
< |
Fig.~\ref{fig:moduletid}. A TIB double-sided module is shown in Fig.~\ref{fig:moduleds} |
| 66 |
> |
A single sided module of the TID ring 3 and a TIB double-sided module |
| 67 |
> |
are shown in Fig.~\ref{fig:moduleds}. |
| 68 |
|
|
| 69 |
|
%\begin{figure}[!htb] |
| 70 |
|
%\begin{center} |
| 80 |
|
\hskip 5mm |
| 81 |
|
\includegraphics[height=0.3\textwidth, width=0.45\textwidth]{Figs/moduleds.pdf} |
| 82 |
|
\end{center} |
| 83 |
< |
\caption{A ring 1 TID module (left panel). A TIB double-sided module, |
| 83 |
> |
\caption{A ring 3 TID module (left panel). A TIB double-sided assembly, |
| 84 |
|
the ``stereo'' module is visible reflected by a mirror (rigth panel).} |
| 85 |
|
\label{fig:moduleds} % Give a unique label |
| 86 |
|
\label{fig:moduletid} |
| 87 |
|
\end{figure} |
| 88 |
|
|
| 89 |
|
%\subsection{The Front-end Electronics} |
| 90 |
< |
The multilayer kapton hybrid circuit holds the near front-end |
| 91 |
< |
electronics consisting of four main components: the readout chips, |
| 92 |
< |
APV25 and three ASICs (the Multiplexer, the PLL and the DCU). All |
| 93 |
< |
devices are addressed and controlled by a I$^2$C serial bus.\\ |
| 94 |
< |
The signals coming from each strip are processed by four or six front-end readout chips |
| 95 |
< |
(APV25), connected to the silicon sensor strips by means of a glass |
| 90 |
> |
The multilayer kapton hybrid circuit holds the module front-end |
| 91 |
> |
electronics consisting of four main components: the readout chips |
| 92 |
> |
(APV25) and three ASICs (the Multiplexer, the PLL and the DCU). All |
| 93 |
> |
devices are addressed and controlled by a I$^2$C serial bus~\cite{ref:i2c}.\\ |
| 94 |
> |
The signals coming from each strip are processed by four or six front-end |
| 95 |
> |
readout chips, connected to the silicon sensor strips by means of a glass |
| 96 |
|
substrate pitch-adapter. The APV25~\cite{ref:apv} |
| 97 |
< |
is a 128 channel chip built in radiation hard 0.25 $\mu$m |
| 97 |
> |
is a 128 channel chip built in radiation tolerant 0.25 $\mu$m |
| 98 |
|
CMOS technology~\cite{ref:radtol}. Each channel consists of a |
| 99 |
|
preamplifier coupled to a CR-RC 50ns shaper. The shaper output is sampled at 40MHz into |
| 100 |
|
a 192 cells pipeline that allows trigger latencies up to 4$\mu$s.\\ |
| 102 |
|
mode}. In the former the shaping time is $50\ns$; in the latter, by |
| 103 |
|
using a deconvolution filter~\cite{ref:deconvolution}, the |
| 104 |
|
effective shaping time is 25ns. In addition, there is also the |
| 105 |
< |
possibility to switch on (Inv) or off an inverter to fully exploit |
| 106 |
< |
the dynamic range of the preamplifier with signals of both |
| 107 |
< |
polarity. Standard operation mode for Silicon Sensor is with |
| 108 |
< |
inverter on. |
| 109 |
< |
{\bf FIX ME: ma serve??? Nel seguito non si fa mai menzione dei vari |
| 110 |
< |
modi di funzionamento dell'APV - forse da aggiungere nela |
| 111 |
< |
descrizione del ped-noi run?} |
| 105 |
> |
possibility to switch on or off an inverter stage which slightly |
| 106 |
> |
decreases the common mode noise contribution. |
| 107 |
> |
% Standard operation mode for Silicon Sensor is with |
| 108 |
> |
% inverter on. |
| 109 |
> |
%%{\bf FIX ME: ma serve??? Nel seguito non si fa mai menzione dei vari |
| 110 |
> |
%% modi di funzionamento dell'APV - forse da aggiungere nela |
| 111 |
> |
%% descrizione del ped-noi run?} |
| 112 |
|
|
| 113 |
|
On receiving a level 1 trigger the APV25 sends out serially |
| 114 |
|
%, at 20MHz rate, |
| 116 |
|
pipeline address and the chip error status; two APV25 are multiplexed |
| 117 |
|
on a differential line by the Multiplexer chip~\cite{ref:mux}. |
| 118 |
|
In absence of data to stream out, for synchronization purposes, the |
| 119 |
< |
APV issues a 25ns pulse called ``tick mark'' |
| 119 |
> |
APV25 issues a 25ns pulse called ``tick mark'' |
| 120 |
|
with a period of 70 clock cycles.\\ |
| 121 |
< |
The PLL chip\cite{ref:pll} allows the clock to be delayed to |
| 121 |
> |
The Phase Locked Loop (PLL) chip~\cite{ref:pll} allows the clock to be delayed by 1.04ns |
| 122 |
> |
steps, to |
| 123 |
|
compensate for path differences of control signals and for any |
| 124 |
|
electronics delay. The PLL also decodes the trigger signals that are |
| 125 |
|
encoded on the clock line.\\ |
| 126 |
< |
The Detector Control Unit (DCU) contains an eight-channel ADC, |
| 126 |
> |
The Detector Control Unit (DCU)~\cite{ref:dcu} contains an eight-channel ADC, |
| 127 |
|
two constant current sources and a temperature sensor. It |
| 128 |
|
monitors two sets of thermistors, one on the sensor |
| 129 |
|
and one on the hybrid, its own internal temperature, the |
| 138 |
|
The Analog-Opto Hybrids~\cite{ref:aoh} (AOH) performs the |
| 139 |
|
electrical-to-optical conversion of the electrical signals of the two |
| 140 |
|
or three APV25 pairs, depending on the module type, by means of |
| 141 |
< |
radiation hard lasers~\cite{Gill:2005ui}. There is one AOH |
| 141 |
> |
radiation tolerant lasers and components\cite{ref:laserdriver}. |
| 142 |
> |
There is one AOH |
| 143 |
|
per module, sitting on a ledge glued on the cooling pipe very close to |
| 144 |
< |
the silicon module hybrid. Multi-mode optical fiber~\cite{ref:opto} |
| 145 |
< |
transport the signal to the FEDs~\cite{ref:fed} for the |
| 146 |
< |
digitization. Each AOH has two or three two meter long pig-tail |
| 144 |
> |
the front-end hybrid. Multi-mode optical fibers~\cite{ref:opto} |
| 145 |
> |
transport the signal to the counting room where the FEDs~\cite{ref:fed} |
| 146 |
> |
convert back the signal to an electrical one and digitize it. |
| 147 |
> |
Each AOH has two or three two meter long pig-tail |
| 148 |
|
optical fibres ending with an optical plug.\\ |
| 149 |
< |
The electrical signals arrive to the AOH through hybrid |
| 149 |
> |
The electrical signals arrive to the AOH through front-end hybrid |
| 150 |
|
kapton cable. The AOH is powered by the same cable. |
| 151 |
|
By means of the AOH control logic the laser working parameters GAIN |
| 152 |
|
and BIAS can be set via $I^2C$ control registers. |
| 153 |
|
The GAIN parameter can be used to compensate the loss of signal |
| 154 |
|
on the optical link to the FED input. The GAIN parameter has four |
| 155 |
|
possible values, 0, 1, 2, 3, corresponding to a nominal |
| 156 |
< |
gain value of 0.5, 0.75, 1, 1.25, respectively, normalized at |
| 157 |
< |
GAIN=3. During normal operation, if no damage was done to the line and |
| 156 |
> |
gain value of 0.5, 0.75, 1, 1.25, respectively. |
| 157 |
> |
During normal operation, if no damage was done to the line and |
| 158 |
|
ideal connections, it is normally set to 1. |
| 159 |
|
The BIAS parameter regulates the current threshold for the laser |
| 160 |
|
diodes and can be set in the range 0$\div$127. The optimal value |
| 169 |
|
``node'' in a ``token-ring'' formed by several daisy-chained CCUs and |
| 170 |
|
known as {\it control ring}. The control ring is mastered by a Front End |
| 171 |
|
Controller, FEC~\cite{ref:opto}, located outside the experiment by |
| 172 |
< |
means of optical signals. The entire TIB and TID contains roughly 100 |
| 172 |
> |
means of optical signals. The entire TIB and TID contains a total of 110 |
| 173 |
|
Control Rings. |
| 174 |
|
|
| 175 |
|
\begin{description} |
| 183 |
|
via a 26 poles flat cable. |
| 184 |
|
To cope with possible CCU failures that would affect the entire ring, the |
| 185 |
|
control ring features the so called {\it redundancy} by means of |
| 186 |
< |
a clever layout, shown in Fig.~\ref{fig:redundancy}, that exploits the |
| 186 |
> |
a {\it double path} layout, shown in Fig.~\ref{fig:redundancy}. |
| 187 |
> |
This design exploits the |
| 188 |
|
two input/output replicas of the CCUs: each CCU is connected to the |
| 189 |
|
two nearby CCUs through the primary circuit (``A'') and to the second |
| 190 |
|
next CCUs through the secondary circuit (``B'') by which a failing CCU |
| 226 |
|
|
| 227 |
|
\subsection{The Mother Cable} |
| 228 |
|
The electrical connections between a group of modules served by the |
| 229 |
< |
same CCU are done by the {\it Mother Cable}~\cite{ref:mc}, a flexible |
| 229 |
> |
same CCU are done by the {\it Mother Cable}~\cite{ref:mc}, a |
| 230 |
|
multi-layer kapton copper circuit. An example is shown in |
| 231 |
|
Fig.~\ref{fig:fotomc}. The mother cable is mounted on the carbon fiber |
| 232 |
|
support structure underneath the modules. |
| 248 |
|
\begin{center} |
| 249 |
|
\includegraphics[width=0.85\textwidth]{Figs/mothercable.pdf} |
| 250 |
|
\end{center} |
| 251 |
< |
\caption{A mother cable mounted on a shell. In the two upper boxes, the detail of the CCU |
| 252 |
< |
installed on MC and the connectors at the edge of the MC.} |
| 251 |
> |
\caption{A TIB mother cable with module connectors and CCU (top); |
| 252 |
> |
details of the CCU and the connectors at the edge of the MC |
| 253 |
> |
(middle); three module assembled string (bottom).} |
| 254 |
|
\label{fig:fotomc} |
| 255 |
|
\end{figure} |
| 256 |
|
|
