| 1 |
sguazz |
1.4 |
\section{TIB and TID layout}
|
| 2 |
|
|
|
| 3 |
|
|
TIB and TID are very compact objects with high readout granularity;
|
| 4 |
|
|
channel and module densities are three to four times larger than in
|
| 5 |
|
|
the other SST subsystems as shown in Table~\ref{table:Density} where
|
| 6 |
|
|
the main parameters of the SST subsystems are
|
| 7 |
|
|
reported. The TIB and TID layout has been designed matching the
|
| 8 |
|
|
following features: simple mechanical structure; easy routing of the
|
| 9 |
|
|
large number of service connections (cooling, readout, controls); easy
|
| 10 |
|
|
component mounting in the case of the TIB non-planar (cylindrical)
|
| 11 |
|
|
geometry; optimization the theta (and phi?) for the TID.
|
| 12 |
|
|
|
| 13 |
|
|
The TIB is structured in four concentric layers. Each layer is
|
| 14 |
|
|
split along the vertical plane at $z=0$ into two almost identical half-layers. Each
|
| 15 |
|
|
half-layer is further split along the horizontal at $y=0$ into two semi-cylindrical
|
| 16 |
|
|
structures, also referred to as ``shells''. The shell structure is a
|
| 17 |
|
|
semi-cylindrical carbon fiber assembly strenghten by two circular
|
| 18 |
|
|
flanges at both ends. Modules and services are hold either on
|
| 19 |
|
|
the external and the internal surfaces. The services are laid down on
|
| 20 |
|
|
the surface and run parallel to the $z$ axis.
|
| 21 |
|
|
% on the surface toward the end (i.e. in the
|
| 22 |
|
|
%direction along which $|z|$ increases).
|
| 23 |
|
|
The modules and the related
|
| 24 |
|
|
services that sit on the same side of a shell at the same $\phi$
|
| 25 |
|
|
coordinate constitute a \textit{string}.
|
| 26 |
|
|
|
| 27 |
|
|
The TID is split into six disks (three per each side of
|
| 28 |
|
|
TIB). The disk is made up by three sub-disks called "rings" since each
|
| 29 |
|
|
ring holds modules at the same radius. The ring structure consists of
|
| 30 |
|
|
a mechanical support made of an annular carbon fiber honeycomb,
|
| 31 |
|
|
hosting modules and services on both sides to decrease the density
|
| 32 |
|
|
and therefore providing a better accessibility during ring integration
|
| 33 |
|
|
and disk assembly.
|
| 34 |
|
|
|
| 35 |
|
|
As a result of the above described structure the TIB/TID system is
|
| 36 |
|
|
divided into two physically separated structures, one located in the
|
| 37 |
|
|
$z > 0$ region and one located in the $z < 0$ region and known as
|
| 38 |
|
|
TIB/TID+ and TIB/TID- respectively. Each TID+ and TID- is obtained by
|
| 39 |
|
|
inserting, positioning and fixing each disk into a carbon fiber
|
| 40 |
|
|
cylinder called {\it Service Cylinder}. Each Service Cylinder has
|
| 41 |
|
|
several holes at the position of disk, in order to allow the
|
| 42 |
|
|
connection of the power lines and to route out all the fibers of the
|
| 43 |
|
|
disk. The Service Cylinder is also used to connect mechanically TIB+/-
|
| 44 |
|
|
and TID+/-, and to route out the services of the TIB and of the TID.
|
| 45 |
|
|
|
| 46 |
|
|
The cooling in the TIB/TID is distributed via aluminum pipe circuits
|
| 47 |
|
|
that are bent into loops and soldered to inlet/outlet manifolds at
|
| 48 |
|
|
the flange for the TIB, and at the ring outer edge for the TID.
|
| 49 |
|
|
The thermal connection between pipes and sensor modules is made with Aluminum ledges which are
|
| 50 |
|
|
precisely glued on the carbon fiber support structure and in good thermal contact with the pipes.
|
| 51 |
|
|
On each ledge there are two threaded M1 holes onto which the modules are tightened.
|
| 52 |
|
|
Precisely drilled slots, coaxial with the threaded holes, are the reference point where
|
| 53 |
|
|
insets are stick in providing mechanical reference for modules. An example for a TIB module
|
| 54 |
|
|
is shown in Fig.~\ref{fig:module_cooling}).
|
| 55 |
|
|
|
| 56 |
|
|
The TIB and TID substructures, 16 shells and 18 rings, are relatively
|
| 57 |
|
|
large-sized: shells hold 135 to 216 modules, rings hold 40 to 48 modules.
|
| 58 |
|
|
Some other relevant specifications of the TIB and TID substructures are
|
| 59 |
|
|
summarized in Table~\ref{table:layers}.
|
| 60 |
|
|
A finished half of the TIB and a TID Disk are shown in
|
| 61 |
|
|
Fig.~\ref{fig:tibtid}. The pictures allow the sub-structures to be
|
| 62 |
|
|
recognized.
|
| 63 |
|
|
|
| 64 |
|
|
|
| 65 |
|
|
|
| 66 |
|
|
\begin{figure}[!htb]
|
| 67 |
|
|
\begin{center}
|
| 68 |
|
|
\includegraphics[width=0.45\textwidth]{Figs/shell.pdf}
|
| 69 |
|
|
% \includegraphics[height=0.5\textwidth]{Figs/TIB-assembled.pdf}
|
| 70 |
|
|
\hskip 1cm
|
| 71 |
|
|
\includegraphics[width=0.45\textwidth]{Figs/TIB_barrel.png}
|
| 72 |
|
|
\end{center}
|
| 73 |
|
|
\caption{A L3 TIB shell (left panel) and half of TIB assembled (right panel).}
|
| 74 |
|
|
\label{fig:tib} % Give a unique label
|
| 75 |
|
|
\end{figure}
|
| 76 |
|
|
|
| 77 |
|
|
\begin{figure}[!htb]
|
| 78 |
|
|
\begin{center}
|
| 79 |
|
|
\includegraphics[height=0.35\textwidth]{Figs/ring.pdf}
|
| 80 |
|
|
% \includegraphics[height=0.5\textwidth]{Figs/TIB-assembled.pdf}
|
| 81 |
|
|
\hskip 3cm
|
| 82 |
|
|
\includegraphics[height=0.35\textwidth]{Figs/TID-disk.pdf}
|
| 83 |
|
|
\end{center}
|
| 84 |
|
|
\caption{A R1 TID ting assembled (left panel) and one TID disk (right panel).}
|
| 85 |
|
|
\label{fig:tid} % Give a unique label
|
| 86 |
|
|
\end{figure}
|
| 87 |
|
|
|
| 88 |
|
|
|
| 89 |
|
|
\begin{table}[!htb]
|
| 90 |
|
|
\begin{center}
|
| 91 |
|
|
%\begin{tabular}{|l||c|c|c|c|c|c|c|}
|
| 92 |
|
|
\caption[smallcaption]{Total number of modules, strips (or electronic readout channels), detector volume and
|
| 93 |
|
|
channel density for the different tracker subsystems. Service access area is also defined
|
| 94 |
|
|
for barrel geometry detectors (TIB and TOB) as their flange area. The channel density in this
|
| 95 |
|
|
area gives also an idea of the complexity of the detector integration.}
|
| 96 |
|
|
\label{table:Density}
|
| 97 |
|
|
\begin{tabular}{|l|ccccccc|}
|
| 98 |
|
|
\hline
|
| 99 |
|
|
& & & & Module & Channel & Service & Service \\
|
| 100 |
|
|
& \# of &\# of & Volume & Density & Density & Area & Density \\
|
| 101 |
|
|
& modules & channels & [m$^3$]& [$\times 10^3$ m$^{-3}$] & [$\times 10^6$ ch m$^{-3}$] & [m$^2$] & [$\times 10^6$ ch m$^{-2}$]\\
|
| 102 |
|
|
%\hline
|
| 103 |
|
|
\hline
|
| 104 |
|
|
TIB & 2724 & 1 787 904 & 0.82 & 3.2 & 2.2 & 1.6 & 1.11\\
|
| 105 |
|
|
%\hline
|
| 106 |
|
|
TID & 816 & 565 248 & 0.5 & 1.6 & 1.1 & & \\
|
| 107 |
|
|
%\hline
|
| 108 |
|
|
TOB & 5208 & 3 096 576 & 5.9 & 0.89 & 0.52 & 5.7 & 0.54\\
|
| 109 |
|
|
%\hline
|
| 110 |
|
|
TEC & 6400 & 3 866 624 & 11 & 0.58 & 0.35 & & \\
|
| 111 |
|
|
\hline
|
| 112 |
|
|
\end{tabular}
|
| 113 |
|
|
\end{center}
|
| 114 |
|
|
\end{table}
|
| 115 |
|
|
|
| 116 |
|
|
|
| 117 |
|
|
\begin{table}[!htb]
|
| 118 |
|
|
\begin{center}
|
| 119 |
|
|
\caption[smallcaption]{Details on the different layers/rings of the TIB/TID. }
|
| 120 |
|
|
\label{table:layers}
|
| 121 |
|
|
%\begin{tabular}{|l||c|c|c|c|c|c|c|}
|
| 122 |
|
|
\begin{tabular}{|l|ccccccc|}
|
| 123 |
|
|
\hline
|
| 124 |
|
|
Layer & \# mechanical & \# cooling & DS/SS & \# of modules & \# of channels & \# Control & \# Mother \\
|
| 125 |
|
|
& structures & circuits & layer & total & per module & Rings & Cables \\
|
| 126 |
|
|
\hline
|
| 127 |
|
|
% \hline
|
| 128 |
|
|
TIB L1 & 4 shells & & DS & & & & \\
|
| 129 |
|
|
TIB L2 & 4 shells & & DS & & & & \\
|
| 130 |
|
|
TIB L3 & 4 shells & & SS & & & & \\
|
| 131 |
|
|
TIB L4 & 4 shells & & SS & & & & \\
|
| 132 |
|
|
TID R1 & 6 rings & 24 & DS & 288 & 768 & 12 & 48 \\
|
| 133 |
|
|
TID R2 & 6 rings & 24 & DS & 288 & 768 & 12 & 48 \\
|
| 134 |
|
|
TID R3 & 6 rings & 24 & SS & 240 & 512 & 12 & 48 \\
|
| 135 |
|
|
\hline
|
| 136 |
|
|
\end{tabular}
|
| 137 |
|
|
\end{center}
|
| 138 |
|
|
\end{table}
|
| 139 |
|
|
|
| 140 |
|
|
|
| 141 |
|
|
%\subsection{Mechanical Structures}
|
| 142 |
|
|
|
| 143 |
|
|
%A TIB shell is shown on Fig.~\ref{fig:tibshell}).
|
| 144 |
|
|
|
| 145 |
|
|
%Each cooling loop hosts three modules placed in a straight row, which is called a
|
| 146 |
|
|
%A string of modules is connected to the same CCU, thus forming a control branch.
|
| 147 |
|
|
|
| 148 |
|
|
%\begin{figure}
|
| 149 |
|
|
%\centering
|
| 150 |
|
|
%\includegraphics[width=\textwidth]{ }
|
| 151 |
|
|
%\caption{TIB shell: are visible the internal and external parts, the cooling pipes and the string}
|
| 152 |
|
|
%\label{fig:tibshell}
|
| 153 |
|
|
%\end{figure}
|
| 154 |
|
|
|
| 155 |
|
|
|
| 156 |
|
|
%\begin{figure}
|
| 157 |
|
|
%\centering
|
| 158 |
|
|
%\includegraphics[width=\textwidth]{ }
|
| 159 |
|
|
%\caption{TID ring }
|
| 160 |
|
|
%\label{fig:tidring}
|
| 161 |
|
|
%\end{figure}
|
| 162 |
|
|
|
| 163 |
|
|
|
| 164 |
|
|
|
| 165 |
|
|
\begin{figure}
|
| 166 |
|
|
\centering
|
| 167 |
|
|
\includegraphics[width=0.6\textwidth]{Figs/module_cooling.pdf}
|
| 168 |
|
|
\caption{Module Cooling.
|
| 169 |
|
|
\textbf{Upper picture:} a whole cooling loop with six ledges to hold three modules and three
|
| 170 |
|
|
smaller ledges to hold Analog Opto-Hybrids (two more cooling loops are partially visible).
|
| 171 |
|
|
\textbf{Lower picture:} a detail of a cooling loop. The cooling fluid direction
|
| 172 |
|
|
is evidenced with blue arrows, and the precision insets for module insertion are circled in
|
| 173 |
|
|
red. A module mounted on the nearby position is also visible.}
|
| 174 |
|
|
\label{fig:module_cooling}
|
| 175 |
|
|
\end{figure}
|
