| 1 |
< |
\section{The Silicon Strip Tracker Layout} |
| 2 |
< |
\label{sec:Layout} |
| 3 |
< |
The CMS SST |
| 4 |
< |
instruments the radial range between 20~cm and 116~cm and $|\eta| < 2.5$ around the |
| 5 |
< |
LHC interaction point. |
| 6 |
< |
The central region ($|z| < 118$ cm |
| 7 |
< |
\footnote{A CMS coordinate system, used through this note, is defined in such a way that |
| 8 |
< |
$z$ is the coordinate along the LHC beam axis, $y$ is the vertical direction and $x$ |
| 9 |
< |
complete the system; the origin being the nominal beam interaction point.}) |
| 10 |
< |
is split into an Inner Barrel (TIB), made of four detector layers, and an |
| 11 |
< |
Outer Barrel (TOB), made of six detector layers. The TIB is shorter than the TOB, and is |
| 12 |
< |
complemented |
| 13 |
< |
by three Inner Disks per side (TID), each Disk being in turn composed of three |
| 14 |
< |
Rings. The forward and backward regions |
| 15 |
< |
(124~cm $ < |z| < $282~cm) are covered by nine Endcap (TEC) disks per side, each one made of |
| 16 |
< |
up to seven rings. |
| 17 |
< |
The two innermost layers of both TIB and TOB as well as rings number one, two and five |
| 18 |
< |
of TEC and one and two of TID are instrumented with double-sided detector modules. |
| 19 |
< |
A complete description of the Silicon Tracker layout (Fig.\ref{fig:layout}) |
| 20 |
< |
can be found elsewhere~\cite{ref:layout}.\\ |
| 1 |
> |
\section{TIB and TID layout} |
| 2 |
> |
|
| 3 |
> |
TIB and TID are very compact objects with high readout granularity; |
| 4 |
> |
channel and module densities are three to four times larger than in |
| 5 |
> |
the other SST subsystems as shown in Table~\ref{table:Density} where |
| 6 |
> |
the main parameters of the SST subsystems are |
| 7 |
> |
reported. The TIB and TID layout has been designed matching the |
| 8 |
> |
following features: simple mechanical structure; easy routing of the |
| 9 |
> |
large number of service connections (cooling, readout, controls); easy |
| 10 |
> |
component mounting in the case of the TIB non-planar (cylindrical) |
| 11 |
> |
geometry; optimization the theta (and phi?) for the TID. |
| 12 |
> |
|
| 13 |
> |
The TIB is structured in four concentric layers. Each layer is |
| 14 |
> |
split along the vertical plane at $z=0$ into two almost identical half-layers. Each |
| 15 |
> |
half-layer is further split along the horizontal at $y=0$ into two semi-cylindrical |
| 16 |
> |
structures, also referred to as ``shells''. The shell structure is a |
| 17 |
> |
semi-cylindrical carbon fiber assembly strenghten by two circular |
| 18 |
> |
flanges at both ends. Modules and services are hold either on |
| 19 |
> |
the external and the internal surfaces. The services are laid down on |
| 20 |
> |
the surface and run parallel to the $z$ axis. |
| 21 |
> |
% on the surface toward the end (i.e. in the |
| 22 |
> |
%direction along which $|z|$ increases). |
| 23 |
> |
The modules and the related |
| 24 |
> |
services that sit on the same side of a shell at the same $\phi$ |
| 25 |
> |
coordinate constitute a \textit{string}. |
| 26 |
> |
|
| 27 |
> |
The TID is split into six disks (three per each side of |
| 28 |
> |
TIB). The disk is made up by three sub-disks called "rings" since each |
| 29 |
> |
ring holds modules at the same radius. The ring structure consists of |
| 30 |
> |
a mechanical support made of an annular carbon fiber honeycomb, |
| 31 |
> |
hosting modules and services on both sides to decrease the density |
| 32 |
> |
and therefore providing a better accessibility during ring integration |
| 33 |
> |
and disk assembly. |
| 34 |
> |
|
| 35 |
> |
As a result of the above described structure the TIB/TID system is |
| 36 |
> |
divided into two physically separated structures, one located in the |
| 37 |
> |
$z > 0$ region and one located in the $z < 0$ region and known as |
| 38 |
> |
TIB/TID+ and TIB/TID- respectively. Each TID+ and TID- is obtained by |
| 39 |
> |
inserting, positioning and fixing each disk into a carbon fiber |
| 40 |
> |
cylinder called {\it Service Cylinder}. Each Service Cylinder has |
| 41 |
> |
several holes at the position of disk, in order to allow the |
| 42 |
> |
connection of the power lines and to route out all the fibers of the |
| 43 |
> |
disk. The Service Cylinder is also used to connect mechanically TIB+/- |
| 44 |
> |
and TID+/-, and to route out the services of the TIB and of the TID. |
| 45 |
> |
|
| 46 |
> |
The cooling in the TIB/TID is distributed via aluminum pipe circuits |
| 47 |
> |
that are bent into loops and soldered to inlet/outlet manifolds at |
| 48 |
> |
the flange for the TIB, and at the ring outer edge for the TID. |
| 49 |
> |
The thermal connection between pipes and sensor modules is made with Aluminum ledges which are |
| 50 |
> |
precisely glued on the carbon fiber support structure and in good thermal contact with the pipes. |
| 51 |
> |
On each ledge there are two threaded M1 holes onto which the modules are tightened. |
| 52 |
> |
Precisely drilled slots, coaxial with the threaded holes, are the reference point where |
| 53 |
> |
insets are stick in providing mechanical reference for modules. An example for a TIB module |
| 54 |
> |
is shown in Fig.~\ref{fig:module_cooling}). |
| 55 |
> |
|
| 56 |
> |
The TIB and TID substructures, 16 shells and 18 rings, are relatively |
| 57 |
> |
large-sized: shells hold 135 to 216 modules, rings hold 40 to 48 modules. |
| 58 |
> |
Some other relevant specifications of the TIB and TID substructures are |
| 59 |
> |
summarized in Table~\ref{table:layers}. |
| 60 |
> |
A finished half of the TIB and a TID Disk are shown in |
| 61 |
> |
Fig.~\ref{fig:tibtid}. The pictures allow the sub-structures to be |
| 62 |
> |
recognized. |
| 63 |
> |
|
| 64 |
> |
|
| 65 |
> |
|
| 66 |
|
\begin{figure}[!htb] |
| 67 |
|
\begin{center} |
| 68 |
< |
\includegraphics[width=0.85\textwidth]{Figs/rz.pdf} |
| 68 |
> |
\includegraphics[width=0.45\textwidth]{Figs/shell.pdf} |
| 69 |
> |
% \includegraphics[height=0.5\textwidth]{Figs/TIB-assembled.pdf} |
| 70 |
> |
\hskip 1cm |
| 71 |
> |
\includegraphics[width=0.45\textwidth]{Figs/TIB_barrel.png} |
| 72 |
|
\end{center} |
| 73 |
< |
\caption{Longitudinal cross section of one quarter of the CMS SST. |
| 74 |
< |
Thicker (blue) segments indicate double-sided silicon microstrip modules. |
| 75 |
< |
The nominal beam interaction point is located in (0,0), dimensions are in mm. |
| 76 |
< |
The pseudorapidity ($\eta$) coverage is also shown.} |
| 77 |
< |
\label{fig:layout} % Give a unique label |
| 73 |
> |
\caption{A L3 TIB shell (left panel) and half of TIB assembled (right panel).} |
| 74 |
> |
\label{fig:tib} % Give a unique label |
| 75 |
> |
\end{figure} |
| 76 |
> |
|
| 77 |
> |
\begin{figure}[!htb] |
| 78 |
> |
\begin{center} |
| 79 |
> |
\includegraphics[height=0.35\textwidth]{Figs/ring.pdf} |
| 80 |
> |
% \includegraphics[height=0.5\textwidth]{Figs/TIB-assembled.pdf} |
| 81 |
> |
\hskip 3cm |
| 82 |
> |
\includegraphics[height=0.35\textwidth]{Figs/TID-disk.pdf} |
| 83 |
> |
\end{center} |
| 84 |
> |
\caption{A R1 TID ting assembled (left panel) and one TID disk (right panel).} |
| 85 |
> |
\label{fig:tid} % Give a unique label |
| 86 |
> |
\end{figure} |
| 87 |
> |
|
| 88 |
> |
|
| 89 |
> |
\begin{table}[!htb] |
| 90 |
> |
\begin{center} |
| 91 |
> |
%\begin{tabular}{|l||c|c|c|c|c|c|c|} |
| 92 |
> |
\caption[smallcaption]{Total number of modules, strips (or electronic readout channels), detector volume and |
| 93 |
> |
channel density for the different tracker subsystems. Service access area is also defined |
| 94 |
> |
for barrel geometry detectors (TIB and TOB) as their flange area. The channel density in this |
| 95 |
> |
area gives also an idea of the complexity of the detector integration.} |
| 96 |
> |
\label{table:Density} |
| 97 |
> |
\begin{tabular}{|l|ccccccc|} |
| 98 |
> |
\hline |
| 99 |
> |
& & & & Module & Channel & Service & Service \\ |
| 100 |
> |
& \# of &\# of & Volume & Density & Density & Area & Density \\ |
| 101 |
> |
& modules & channels & [m$^3$]& [$\times 10^3$ m$^{-3}$] & [$\times 10^6$ ch m$^{-3}$] & [m$^2$] & [$\times 10^6$ ch m$^{-2}$]\\ |
| 102 |
> |
%\hline |
| 103 |
> |
\hline |
| 104 |
> |
TIB & 2724 & 1 787 904 & 0.82 & 3.2 & 2.2 & 1.6 & 1.11\\ |
| 105 |
> |
%\hline |
| 106 |
> |
TID & 816 & 565 248 & 0.5 & 1.6 & 1.1 & & \\ |
| 107 |
> |
%\hline |
| 108 |
> |
TOB & 5208 & 3 096 576 & 5.9 & 0.89 & 0.52 & 5.7 & 0.54\\ |
| 109 |
> |
%\hline |
| 110 |
> |
TEC & 6400 & 3 866 624 & 11 & 0.58 & 0.35 & & \\ |
| 111 |
> |
\hline |
| 112 |
> |
\end{tabular} |
| 113 |
> |
\end{center} |
| 114 |
> |
\end{table} |
| 115 |
> |
|
| 116 |
> |
|
| 117 |
> |
\begin{table}[!htb] |
| 118 |
> |
\begin{center} |
| 119 |
> |
\caption[smallcaption]{Details on the different layers/rings of the TIB/TID. } |
| 120 |
> |
\label{table:layers} |
| 121 |
> |
%\begin{tabular}{|l||c|c|c|c|c|c|c|} |
| 122 |
> |
\begin{tabular}{|l|ccccccc|} |
| 123 |
> |
\hline |
| 124 |
> |
Layer & \# mechanical & \# cooling & DS/SS & \# of modules & \# of channels & \# Control & \# Mother \\ |
| 125 |
> |
& structures & circuits & layer & total & per module & Rings & Cables \\ |
| 126 |
> |
\hline |
| 127 |
> |
% \hline |
| 128 |
> |
TIB L1 & 4 shells & & DS & & & & \\ |
| 129 |
> |
TIB L2 & 4 shells & & DS & & & & \\ |
| 130 |
> |
TIB L3 & 4 shells & & SS & & & & \\ |
| 131 |
> |
TIB L4 & 4 shells & & SS & & & & \\ |
| 132 |
> |
TID R1 & 6 rings & 24 & DS & 288 & 768 & 12 & 48 \\ |
| 133 |
> |
TID R2 & 6 rings & 24 & DS & 288 & 768 & 12 & 48 \\ |
| 134 |
> |
TID R3 & 6 rings & 24 & SS & 240 & 512 & 12 & 48 \\ |
| 135 |
> |
\hline |
| 136 |
> |
\end{tabular} |
| 137 |
> |
\end{center} |
| 138 |
> |
\end{table} |
| 139 |
> |
|
| 140 |
> |
|
| 141 |
> |
%\subsection{Mechanical Structures} |
| 142 |
> |
|
| 143 |
> |
%A TIB shell is shown on Fig.~\ref{fig:tibshell}). |
| 144 |
> |
|
| 145 |
> |
%Each cooling loop hosts three modules placed in a straight row, which is called a |
| 146 |
> |
%A string of modules is connected to the same CCU, thus forming a control branch. |
| 147 |
> |
|
| 148 |
> |
%\begin{figure} |
| 149 |
> |
%\centering |
| 150 |
> |
%\includegraphics[width=\textwidth]{ } |
| 151 |
> |
%\caption{TIB shell: are visible the internal and external parts, the cooling pipes and the string} |
| 152 |
> |
%\label{fig:tibshell} |
| 153 |
> |
%\end{figure} |
| 154 |
> |
|
| 155 |
> |
|
| 156 |
> |
%\begin{figure} |
| 157 |
> |
%\centering |
| 158 |
> |
%\includegraphics[width=\textwidth]{ } |
| 159 |
> |
%\caption{TID ring } |
| 160 |
> |
%\label{fig:tidring} |
| 161 |
> |
%\end{figure} |
| 162 |
> |
|
| 163 |
> |
|
| 164 |
> |
|
| 165 |
> |
\begin{figure} |
| 166 |
> |
\centering |
| 167 |
> |
\includegraphics[width=0.6\textwidth]{Figs/module_cooling.pdf} |
| 168 |
> |
\caption{Module Cooling. |
| 169 |
> |
\textbf{Upper picture:} a whole cooling loop with six ledges to hold three modules and three |
| 170 |
> |
smaller ledges to hold Analog Opto-Hybrids (two more cooling loops are partially visible). |
| 171 |
> |
\textbf{Lower picture:} a detail of a cooling loop. The cooling fluid direction |
| 172 |
> |
is evidenced with blue arrows, and the precision insets for module insertion are circled in |
| 173 |
> |
red. A module mounted on the nearby position is also visible.} |
| 174 |
> |
\label{fig:module_cooling} |
| 175 |
|
\end{figure} |
| 31 |
– |
The whole tracker region is embedded into the CMS 4~Tesla solenoidal magnetic field. |
| 32 |
– |
Charged particle transverse momentum resolution of about 1.5\% for centrally-produced |
| 33 |
– |
muon of 100~GeV/$c$ is expected~\cite{ref:ptdr}. \\ |
| 34 |
– |
From the detector construction point of view it is important to note that the TIB/TID |
| 35 |
– |
system is divided into two physically separated structures: TIB/TID+, which is located in the |
| 36 |
– |
$|z| > 0$ region and TIB/TID-, located in the $|z| < 0$.\\ |
| 37 |
– |
The entire tracker is inserted in a carbon fiber Support Tube which is attached to |
| 38 |
– |
the Electromagnetic Calorimeter and insulated by the rest of the experiment by a |
| 39 |
– |
'Thermal Shield'. |
